View source for ZL30PRGv2-1 - Kamamilabs.com

__jzpdf__
 
<center>
[[File:Zl30prgv2-1_01.jpg|none|600px|thumb|center]]
</center>
====== Description ======
An innovate programmer--debugger with the USB interface. It supports the STM32 microcontrollers thru SWD interface. ZL30PRGv2-1 is fully compatible with the STMicroelectronics ST-Link/V2-1. It also has the function of USB-UART converter.

The programmer is working with the PC using USB interface. The ZL30PRGv2-1 is supported by popular IDE's: uVision (by Keil/ARM, for STM32), IAR Embedded Workbench (by IAR, for STM32), True Studio (by Atollic, for STM32), VX-toolset for ARM Cortex-M (by TASKING, for STM32).

<center>
[[File:Zl30prgv2-1_02.jpg|none|600px|thumb|center]]
</center>

===== Paramters =====
*embedded IDC20 female connector,
*allows to flash and debug STM32 microcontrollers
*fully compatbile with the ST-Link/V2-1 (STMicroelectronics),
*it works with: µVision (Keil), IAR Embedded Workbench (IAR), True Studio (Atollic), VX-toolset for ARM Cortex-M (TASKING),
*embedded microUSB connector,
*an USB-UART function (with pinout compatble with KAMAMI KAmodRS),
*supplied thru USB,
*possibility of firmware upgrade
*target Voltages range:
**SWD: 1.65...3.6V,
*Working temperature range: 0...50°C.

===== Standard equipment =====
<center>
{| class="wikitable"  style="width: 1000px;"
|-
! style="text-align: center;"|Code
! style="text-align: center;"|Description
|-
| style="text-align: center;"|<b>ZL30PRGv2-1</b>
| style="text-align: left;"|
*Programmer
*USB A/B-micro cable
|}
</center>
===== Connecting the programmer to a STM32 target device =====
SWD signals for programming and debugging the STM32 targets are present on the IDC20 connector. Its pin-out is compatbile with the industrial 20-pin JTAG standard (as illustrated on the drawings below), so the programmer could work with any STM32 evaluation boards which uses IDC20 JTAG connector (ZL27ARM, ZL30ARM, STM32Butterfly – Kamami, Keil/ARM evaluation boards, etc).
<center>
{| class="wikitable"  style="width: 800px;"
|-
! style="text-align: left;"|Note!
The programmer does not support JTAG interface!
|}
</center>

<center>
[[File:Zl30prgv2-1_03.JPG|none|250px|thumb|center]]
</center>

<center>
{| class="wikitable"  style="width: 800px;"
|-
! style="text-align: left;"|Note!
ZL30PRGv2-1 is powered from the USB connector. The supply voltage is not forwarded to the programmed/debugged target, so it needs to be supplied externally.
|}
</center>

<center>
[[File:Zl30prgv2-1_04_en.JPG|none|700px|thumb|center]]
</center>

===== Interfacing UART signals to the programmer =====
The programmer has a Virtual COM Port (VCOM) option. RxD and TxD signals are available on the connector (as illustrated on the photo below). The drilled pads allow to solder-in Goldpin headers. By this function, the programmer can replace the KAmodRS module.

<center>
[[File:Zl30prgv2-1_05.jpg|none|800px|thumb|center]]
</center>

===== Additional information =====
[https://www.segger.com/products/debug-probes/j-link/models/other-j-links/st-link-on-board/ Converting ST-Llink Into a J-Link]