KAmodPCA9533: Difference between revisions
From Kamamilabs.com - Wiki
No edit summary |
Anna Kubacka (talk | contribs) No edit summary |
||
| (2 intermediate revisions by one other user not shown) | |||
| Line 1: | Line 1: | ||
__jzpdf__ | __jzpdf__ | ||
====== Description ====== | ====== Description ====== | ||
[https://kamami.pl/kamod-kamami/ | [https://kamami.pl/kamod-kamami/573218-kamodpca9533-modul-ze-sterownikiem-led.html KAmodPCA9533] is a module with LED dimmer from NXP. The board is equipped with a Pmod I2C standard connector and a KAMAMI connector, that allow to easy connection of the module to the evaluation kits. Due to its small dimensions, the product can be used in many development projects, while the Pmod loop connector allows to connect the boards in the series. | ||
<center> | <center> | ||
[[File:KAmodPCA9533_modul.png|none|400px|thumb|center]] | [[File:KAmodPCA9533_modul.png|none|400px|thumb|center]] | ||
| Line 119: | Line 119: | ||
*[https://download.kamami.pl/p573218-PCA9533%20datasheet.pdf PCA9533 IC datasheet] | *[https://download.kamami.pl/p573218-PCA9533%20datasheet.pdf PCA9533 IC datasheet] | ||
*[https://download.kamami.pl/p573218-OSTBMAS2C1A%20datasheet.pdf OSTBMAS2C1A LED datasheet] | *[https://download.kamami.pl/p573218-OSTBMAS2C1A%20datasheet.pdf OSTBMAS2C1A LED datasheet] | ||
*[https://download.kamami.pl/p573218-KAmodPCA9533-lib.zip Library for PCA9533 (C language)] | |||
Latest revision as of 10:26, 23 September 2020
Description
KAmodPCA9533 is a module with LED dimmer from NXP. The board is equipped with a Pmod I2C standard connector and a KAMAMI connector, that allow to easy connection of the module to the evaluation kits. Due to its small dimensions, the product can be used in many development projects, while the Pmod loop connector allows to connect the boards in the series.
Basic features and parameters
- PCA9533 chip from NXP
- 4 LED brightness control
- Two programmable blink rates and duty cycles coupled to the output PWM with frequency from 0.591 Hz to 152 Hz
- 256 brightness steps
- Pins not used as LED drivers can be used as regular GPIOs
- Internal oscillator
- I2C-bus interface
- LED RGB OSTBMAS2C1A
- Connector compatible with the Pmod standard, allows serial connection of Pmod I2C modules
- The connector complies with the KAMAMI standard
- Embedded jumpers activating pull-up on I2C bus lines
- Possibility to supply voltage from 2.3...5.5V
- Mounting holes with a diameter of 2.5mm
- Dimensions: 61.2mm x 20.3mm x 10mm
Standard equipment
| Code | Description |
|---|---|
| KAmodPCA9533 |
|
Electrical schematic
Output description - Pmod standard connector
 |
JP1 (male connector) | JP2 (female connector) | Function |
|---|---|---|---|
| VDD | VDD | Power supply of module (max. 3,6 V) | |
| GND | GND | ||
| SDA | SDA | Data line of I2C bus | |
| SCL | SCL | Clock line of I2C bus | |
| RST | RST | - | |
| INT | INT | - |
Output description – KAMAMI standard connector
 |
Pin number | Function |
|---|---|---|
| 1 (VDD_5V) | Power supply of module (max. 5,5 V) | |
| 2 (SCL) | Clock line of I2C bus | |
| 3 (SDA) | Data line of I2C bus | |
| 4 (GND) | Ground |
I2C bus lines
The KAmodPCA9533 module is equipped with jumpers allowing to connect pull-up resistors to the positive power pole to the I2C bus line. The jumpers give the possibility of independent enabled of the pull-up for the SDA and SCL lines.
LED RGB
The KAmodPCA9533 module is equipped with an RGB OSTBMAS2C1A diode with a common anode. The diode is connected to the LED0, LED1 and LED2 pins of the PCA9533 chip with the use of current limiting resistors.
Dimensions
