KAmodBT-HC05: Difference between revisions
From Kamamilabs.com - Wiki
m Text replacement - "[[Plik:" to "[[File:" |
No edit summary |
||
| (6 intermediate revisions by 4 users not shown) | |||
| Line 1: | Line 1: | ||
__jzpdf__ | __jzpdf__ | ||
====== Description ====== | ====== Description ====== | ||
[https://kamami.pl/ | [https://kamami.pl/en/bluetooth-modules/557976-kamodbt-hc05-bluetooth-v2-0-edr-module-with-hc-05-system-5906623432516.html KAmodBT-HC05] is a configurable (by using AT commands) Bluetooth module. Module has integrated LEDs, which signal work mode and connection state with device. Thanks to the small sizes and embedded translator of levels on TxD / RxD lines, module can be used in a lot of development projects. | ||
<center> | <center> | ||
[[File:KAmodBT-HC05_modul.png|none|400px|thumb|center]] | [[File:KAmodBT-HC05_modul.png|none|400px|thumb|center]] | ||
| Line 82: | Line 82: | ||
===== External links ===== | ===== External links ===== | ||
*[http://download.kamami.pl/p557976-kamodbt_hc05_datasheet.pdf HC-05 module datasheet] | *[http://download.kamami.pl/p557976-kamodbt_hc05_datasheet.pdf HC-05 module datasheet] | ||
Latest revision as of 16:20, 1 November 2024
Description
KAmodBT-HC05 is a configurable (by using AT commands) Bluetooth module. Module has integrated LEDs, which signal work mode and connection state with device. Thanks to the small sizes and embedded translator of levels on TxD / RxD lines, module can be used in a lot of development projects.
Basic features and parameters
- HC-05 module with integrated antenna, complies with Bluetooth v2.0 specification
- UART interface with programmable data transfer speed (baudrate)
- Typical receiver sensitivity: -80dBm
- Up to +4dBm RF transmit power
- Embedded voltage regulator
- Possibility of power supply with voltage in range: 2.1V…5.5V
- Embedded voltage level translator on UART lines (TxD, RxD)
- Embedded LED work mode (MODE) and pairing state (PAR)
- Embedded button (running configuration mode)
- KEY and nRST signals on connector
- Sizes: 34.2mm x 27mm x 5mm
Standard equipment
| Code | Description |
|---|---|
| KAmodBT-HC05 |
|
Electrical schematic
Output description
 |
JP1 | Function |
|---|---|---|
| +3,3V | Module power supply | |
| +V | ||
| GND | ||
| RxD | Receiver UART line (with voltage level translator) | |
| TxD | Transmitter UART line (with voltage level translator) | |
| nRST | Device reset (enabled with low state) | |
| KEY | Button for changing work mode (maximum voltage on line: 3.6V) |
MODE and PAR LEDs
KAmodBT-HC05 module was equipped with LEDs to signalling work mode and connection state with device. By default module settings, green MODE led signals visibility mode (blinking 5 times per second), configuration mode (blinking every 2s) and active mode (double blink every 2s). PAR LED (red) is ON, when communication with device is active.
Work mode button
KAmodBT-HC05 module was equipped with button for changing work mode - short holding in power supply enabled moment (or by reset) allow to run configuration mode of module (with using AT commands). Parallel with button is connected also KEY line - setting on this line HIGH signal (maximum 3.6V) allow to control work mode from e.g. microcontroller level. This line is pulled down with resistor 10kΩ.
