KAmodRPi-Pmod-HAT

Description

KAmodRPi-Pmod-HAT is a HAT for Raspberry Pi 4B/3B+/3B/2B/B+ minicomputers that allows use of the communication interfaces available on the 40-pin minicomputer connector. The overlay provides connectors in the Pmod standard and in the KAMAMI standard for I2C, SPI and UART interfaces.

Basic parameters

• Expansion module for Raspberry Pi 4B, 3B+, 3B, 2B, B+ minicomputers
• Embedded ID-EEPROM memory
• Connectors for I2C, SPI and UART interfaces
• Pmod connectors
• KAMAMI connectors
• 40-pin through connector compatible with the Raspberry Pi standard
• Embedded jumpers enabling pull-up on I2C bus lines
• Mounting holes with a diameter of 2.5 mm
• Dimensions: 65 mm x 56 mm x 10 mm

Standard equipment

Code	Description
KAmodRPi-Pmod-HAT	Aassembled and launched module Four spacers with a set of screws for mounting

Schematic

Pin description - I2C KAMAMI standard connector

	Pin number	Function
	1 (VDD_3,3V)	Power supply (max. 3,3 V)
	2 (SCL)	Clock line of the I2C bus
	3 (SDA)	Data line of the I2C bus
	4 (GND)	Ground

Opis wyprowadzeń – złącze SPI standardu KAMAMI

	Pin number	Function
	1 (VDD_3,3V)	Power supply (max. 3,3 V)
	2 (CS)	CS line of the SPI bus
	3 (MOSI)	Data line to peripheral chip of the SPI bus
	4 (MISO)	Data line from peripheral chip of the SPI bus
	5 (CLK)	Clock line of the SPI bus
	6 (GND)	Ground

Opis wyprowadzeń – złącze I2C standardu Pmod

	Pin number	Function
	1, 2 (SCL)	Clock line of the I2C bus
	3, 4 (SDA)	Data line of the I2C bus
	5, 6 (GND)	Ground
	7, 8 (VDD_3,3V)	Power supply (max. 3,3 V)
	9, 10 (INT)	Interrupt line
	11, 12 (RESET)	Reset line

Opis wyprowadzeń – złącze SPI standardu Pmod

	Pin number	Function	Pin number	Function
	1 (CS)	CS line of the SPI bus	7 (INT SPI)	Interrupt line
	2 (MOSI)	Data line to peripheral chip of the SPI bus	8 (RESET SPI)	Reset line
	3 (MISO)	Data line from peripheral chip of the SPI bus	9 (GPIO20)	Linia I/O
	4 (CLK)	Clock line of the SPI bus	10 (GPIO18)	Linia I/O
	5 (GND)	Ground	11 (GND)	Ground
	6 (VDD_3,3V)	Power supply (max. 3,3 V)	12 (VDD_3,3V)	Power supply (max. 3,3 V)

Opis wyprowadzeń – złącze UART standardu Pmod

	Pin number	Function
	1 (CTS)	CTS line of the UART bus
	2 (TXD)	TX data line of the UART bus
	3 (RXD)	RX data line of the UART bus
	4 (RTS)	RTS line of the UART bus
	5 (GND)	Ground
	6 (VDD_3,3V)	Power supply (max. 3,3 V)

I2C bus lines

The KAmodRPi-Pmod-HAT module is equipped with jumpers that allow the connection of pull-up resistors to the VCC to the I2C bus line. Jumpers allow the independent activation of chin up for SDA and SCL lines.

Write protection of the ID EEPROM memory

The KAmodRPi-Pmod-HAT module is equipped with a jumper that allows write block to EEPROM memory. Write Protect protects against unwanted attempts to write data to memory.

Dimensions