Difference between revisions of "KAmodLPS331"
Anna Kubacka (talk | contribs) |
m (Text replacement - "[[Plik:" to "[[File:") |
||
| Line 5: | Line 5: | ||
<center> | <center> | ||
| − | [[ | + | [[File:KAmodLPS331_modul.png|none|400px|thumb|center]] |
</center> | </center> | ||
| Line 38: | Line 38: | ||
===== Electrical schematic ===== | ===== Electrical schematic ===== | ||
<center> | <center> | ||
| − | [[ | + | [[File:KAmodLPS331_schemat.png|none|800px|thumb|center]] |
</center> | </center> | ||
===== Outputs description ===== | ===== Outputs description ===== | ||
| Line 45: | Line 45: | ||
{| class="wikitable" style="width: 1000px;" | {| class="wikitable" style="width: 1000px;" | ||
|- | |- | ||
| − | ! style="text-align: center;" rowspan="10"| [[ | + | ! style="text-align: center;" rowspan="10"| [[File:KAmodLPS331 obrys PCB.png|center|200px]] |
! style="text-align: center;"|JP1 | ! style="text-align: center;"|JP1 | ||
! style="text-align: center;"|I2C | ! style="text-align: center;"|I2C | ||
Revision as of 19:50, 5 July 2018
Contents
Description
KAmodLPS331 is a module, which bases on absolute pressure sensors LPS331. It is characterized by i.a. wide range and high resolution of measurement. Module allows to measurement of absolute pressure in range 260 - 1260hPa. Thanks to embedded voltage regulator and logic level translator, module can be used in system with power supply 2.5 - 5.5V.
Basic features and parameters
- LPS331AP chip (MEMS pressure sensor) from STMicroelectronics
- Measurement range: from 260 to 1260mbar of absolute pressure (260 - 1260hPa)
- Measurement resolution: 0,02hPa RMS
- Power supply voltage: 2.5V - 5.5V
- Power consumption: 7mA
- Measurement data rate (ODR): 1-25[Hz]
- ADC converter resolution: 24 bits
- Communication interface: SPI / I2C
- Embedded voltage regulator and logic level translator (SDA and SCL lines)
- Interrupt output / data ready output /FIFO flag
- Place for soldering of pin header
- Mounting holes 3mm
- Module size (without connector): 27mm x 15mm x 3mm
Standard equipment
| Code | Description |
|---|---|
| KAmodLPS331 |
|
Electrical schematic
Outputs description
 |
JP1 | I2C | SPI 3-wire | SPI 4-wire |
|---|---|---|---|---|
| +3.3V | Module power supply | |||
| +VIN | ||||
| GND | ||||
| SDA/SDI/SDO | SDA | SDI/SDO | SDI | |
| SCL/SPC | SCL | SPC | SPC | |
| SDO/SA0 | SA0 | - | SDO | |
| CS | CS | CS | CS | |
| INT2/DRDY | Interrupt 2 output / data ready output | |||
| INT1/DRDY | Interrupt 2 output / data ready output | |||
External links
- LPS331 chip datasheet
- Library for Arduino
- [Project] 'KAmodLPS331- czujnik ciśnienia atmosferycznego i KAmduino UNO' on MIKROKONTROLER.PL page
Kategoria:Moduły peryferyjne KAmod (Kamami) Kategoria:Zawartość